Primary Logo
Warewashing green&clean multi-rinse Rack Type, Energy Saving Device, ZERO LIME Device, electric, 250r/h, R>L (COD 535020)
Where to buy
Multi Rinse Rack Type dishwashers - 250 racks per hour

Warewashing
green&clean multi-rinse Rack Type, Energy Saving Device, ZERO LIME Device, electric, 250r/h, R>L

COD 535020

Multi Rinse Rack Type Dishwasher, 250 racks/hour, electric, Right>Left, Energy Saving Device, large pre-wash, constant rinse, self cleaning, ZERO LIME Device, CLEAR BLUE Filtering System, WASH-SAFE CONTROL, touch screen, variable speeds, insulated doors,

Alternative green solution available.

Where to buy
Register your product

Suggested
for you.

Go premium,
go green.

go to product
Multi Rinse Rack Type dishwashers - 250 racks per hour

Warewashing
green&clean multi-rinse Rack Type, Ventless heat pump, ZERO LIME Device, electric, 250r/h,right>left

COD 535010

Multi Rinse Rack Type Dishwasher, 250 racks/hour, electric, Right>Left, ventless heat pump, large pre-wash, constant rinse, self cleaning, ZERO LIME Device, CLEAR BLUE Filtering System, WASH-SAFE CONTROL, touch screen, variable speeds, insulated doors, WR

Suggested green version.

Where to buy
Register your product
go to product

Specifications

  • Air humidity (top, exit): 0 / 100 % r.h.

    Latent heat: 6200 W

    Sensible heat: 5100 W

    Air flow (top, exit): 0 / 145 m³/h

    Air temperature: 0 - 45 °C

    The data is measured at exhaust points at 25°C and 60% r.h. ambient conditions, 18°C inlet water temperature and refer only to the machine.

    This model requires a ventilation hood. Please refer to the attached "Recommended Exhaust Hood Design".

  • When the machine runs at DIN 10510 compliant speed.

    At average working conditions.

    Supply voltage: 380-415 V/3N ph/50 Hz

    Energy consumption: 27.9 kWh

    Wash tank heating elements: 14 kW

    Triple tank heating elements: 7 kW

    Default Installed Power: 32.8 kW

    Boiler heating elements: 7 kW

    Electrical power min: 25.8 kW

    Wash pump size: 1.5 kW

    Rinse pump size (final, duo, triple): 0.55 / 0.32 / 0.32 kW

  • The higher the temperature, the faster the warm-up.
    Recommended temperature: 50°C.

    When below 7°fH/4°dH special detergent and rinse aid are needed.

    Inlet water line size: G 3/4"

    Inlet cold water line size: G 3/4"

    Drain line size: 50mm

    Inlet water supply pressure: 1.5-6 bar

    Inlet water supply temperature (wash and rinse): 5 - 65°C

    Inlet water supply temperature (rinse and pre-wash): 5 - 30 °C

    Inlet water supply hardness: 0-14 °fH / 0-8°dH

    Flow rate of wash pump: 500 l/h

    Peak rate of drain flow: 1.8 l/s

    Wash tank size: 70 l

    Duo rinse tank size: 20 l

    Triple rinse tank size: 20 l

    Rinse water consumption:

  • For transportation purpose only, the depth can be reduced to 795mm by removing the control box and the door handles.

    Reference norm used to measure the noise: IEC60335-2-58 annex AA.

    Height with door open: 2095 mm

    Charging hole size (width): 530 mm

    Productivity per hour (max. speed): 250 racks/4500dishes

    External dimensions, Width: 2970 mm

    External dimensions, Depth: 895 mm

    Productivity per hour (DIN compliant speed): 168 racks/3024 dishes

    External dimensions, Height: 1785 mm

    Charging hole size (height): 490 mm

    Productivity per hour (NSF compliant speed): 150 racks/2700 dishes

    Wash Temperature: 55 - 65 °C

    Duo rinse temperature: 75-80 °C

    Net weight: 553 kg

    Shipping weight: 630 kg

    Final rinse temperature: 85 °C

    Shipping height: 1980 mm

    Shipping width: 1040 mm

    Shipping depth: 3450 mm

    Shipping volume: 7.1 m³

    Table to table distance: 2970 mm

    Triple rinse temperature: 70 - 75 °C

  • Noise level: <62 dBA

    Rinse water consumption at max. speed: 100 l/h

Product Features

All chambers without internal pipes and therefore no hidden dirt traps.
ZERO LIME Device as a fully automatic cycle ensures total scale removal from the boiler, the hydraulic circuit, the washing chamber and the rinsing chamber allowing ultimate performances and lower energy consumption thanks to highly efficient heating elements.
Built-in Energy Saving Device (ESD) utilizes the hot steam generated by the machine in the rinse and wash tanks to heat up incoming cold water up to 55°C before entering the boiler, thus saving energy.
Multi-rinse technology guarantees rinse water consumption of 0.4 liters/rack regardless of the conveyor speed to ensure low energy, water, detergent and rinse aid consumption.
Auto-start/stop equipped in different zones ensures that the zone runs only when a rack is passing through it. This reduces water, energy, chemical consumption and noise.
Deep drawn pressed wash tank with fully rounded corners, sloped towards the drain to prevent dirt build up provides fast drainage in only a few minutes. Pressed wash tank with no welded points offer a guaranteed water tight solution.
Automatic back-up mode is activated when a failure occurs. Guided troubleshooting for fast fixes including 300 precises notifications and 23 easy-to-follow processes.
Maximum Water Contact (MWC) wash arms are positioned along the full length of the wash tank.
Maximum capacity per hour of 250 racks easy to switch to DIN 10510 or NSF ANSI 3 compliant speed.
Unit equipped with USB port making it simple to read data such as machine identification, counters and consumption, components, devices and alarm logs. Machine parameters can be uploaded and downloaded and firmware updated.
Splashhood at the entrance avoids water spilling outside the machine.
All internal components: wash and rinse arms, tank filters, curtains can be easily removed for cleaning.
Automatic drain, clean and sanitize cycles featured as standard. The internal chambers, including the internal doors are completely cleaned or sanitized avoiding bacteria proliferation for maximum hygiene and reducing manual work/time for operator.
Intuitive touch screen control panel features user-friendly display to easily operate the machine and to monitor machine status. Three different levels of interaction are available each show relevant messages and information to the operator, the general maintenance staff and the authorized service partners.
Pre-wash section uses cold water so food remains are not "baked" onto the plates in order to have better pre-wash performance.
Three conveyor speeds can be selected through the control panel by the operator and customized on site.
Built-in WASH-SAFE CONTROL system raises water temperature to 85°C to sanitize the rinse water. No external boiler is required. Built-in air break and rinse booster pump ensure constant temperature and pressure throughout the rinsing cycle regardless of the inlet water condition.
CLEAR BLUE filtering system removes soil from the wash water providing cleaner water and highly active detergent thus ensuring better washing performance and lower running costs.
Built-in drain valve in the tanks allows automatic dump and fill to refresh the water in the tank without any interruption of the washing process.
Adjustable feet for full access underneath the machine for cleaning.
Multi-rinse arms in combination with double rinse tanks re-use final rinsing water in several phases to ensure hygiene and complete detergent removal on the washed wares.
Large counter balanced inspection doors allow unrestricted all-round access to the wash and rinse area. Door is insulated with injected foam. This adds strength as well as reduces noise and heat loss.
Self-draining wash pumps provide maximum hygiene and all wash and rinse zones drain automatically at the push of a button.
IP25 protection against water jets, solid objects and small animals (larger than 6 mm).
All electric components are put in one IP65 central box isolated from water and steam to ensure high reliability.
All main components made in heavy duty anti-corrosive 304 type stainless steel: external front, side panels and internal chambers, wash and rinse arms, doors and rack transportation system.
The unit is built on modularity concept for easy to add pre-wash, wash and up to 2 dryer modules onsite.
External pre-arrangement for inlet water, drain water, detergent & rinse aid connections for fast and easy installation on both sides of the unit.
Dishwasher structure is held together with a solid 50 x 50 mm stainless steel frame to provide long-term sturdiness.
Modularity design allows the machine not only be disassembled for delivery and re-assembled at customer’s site, but also to be customized and upgraded on-site and over time.
Table-to-table length, 2670mm.

Included Accessories

Image
Quantity
Code
Description
Quantity: 1
Code: 865280
Kit splash hood for rack type with ESD
Quantity: 1
Code: 865282
Kit delime for rack type

Complete the form below to request more information

Do you need support
for this product?

Service network

Interested in
this product?

Where to buy

Do you own
this product?

User manuals (login required)

Let us provide more for
your business!

Register your product (login required)

Select your country

 

Global

Global

Americas

North America

América Latina (Español)

Brasil

Middle East & Africa

Middle East & Africa (English)

Asia-Pacific

South East Asia and India (English)

Malaysia (English)

Australia

中国

日本

New Zealand and Pacific Islands

ประเทศไทย

Europe

België

Belgique

Česká Republika & Slovenská Republika

Danmark

Deutschland

Österreich

Eesti

España

France

Ελληνικά

Hrvatska

Italia

Magyarország

Nederland

Norge

Polska

Schweiz

Suomi

Sverige

Türkiye

UK & Ireland

CIS

Armenia, Azerbaijan, Georgia, Kazakhstan, Kyrgyzstan, Moldova, Ukraine, Uzbekistan (English)

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×